In this article we are going to talk about modern two-stroke technology. While a two-stroke engine is one of the simplest engine designs, modern technology is being applied to help improve performance and efficiency of today’s 2 stroke engines. Read the article below.
Modern two-stroke engines require advanced oilby Leonard Groom III | AMSOIL Technical Product Manager – Powersports
Like the engine in your car or truck, the two-stroke engines that power your snowmobile, chainsaw or outboard motor are growing more sophisticated with each passing year. The same demands driving changes in the automotive market are influencing two-stoke equipment as well – the government mandates reduced exhaust emissions, while consumers want increased fuel economy and more power.What’s a two-stroke engine manufacturer to do? These three areas of importance – reduced emissions, increased fuel economy and maximum performance – don’t play well together. Given the constraints of two-stroke engine design, it’s extremely difficult to build an engine that hits all three targets. Because they don’t contain intake and exhaust valves like a four- stroke engine, controlling emissions in two-strokes is a big challenge. One strategy in today’s oil-injected engines is to adjust the fuel/oil ratio to use less oil. While this reduces emissions, it comes at a cost since using less oil increases operating temperatures and invites several problems.
Excessive heat breaks down the oil and leads to deposits that cause piston rings to stick, robbing the engine of horsepower and reducing performance. In extreme cases, stuck rings can score the cylinder wall and piston skirt, leading to catastrophic failure. To stand up in this intense environment, modern two-strokes require oils with improved heat resistance and lubricity to deliver the necessary level of wear protection. This bodes well for AMSOIL Dealers since conventional lubricants are quickly being left behind.
With snowmobile season gearing up, it’s a great time to look at a couple snowmobile engines that offer examples of the innovation we’re seeing in the two-stroke market. The Arctic Cat* C-TEC* uses electronics that adjust the fuel/oil ratio depending on operating conditions. In one promotional Arctic Cat video, we’re told to expect fuel/oil ratios as high as 65:1, depending on conditions, in the C-TEC2 engine. Less oil means lubrication becomes more challenging. What little oil is available to protect critical engine parts must reach components quickly, particularly in sub-zero cold, and stand up to intense heat and friction once it’s distributed throughout the engine. The C-TEC uses an interesting configuration to deliver oil to the wrist pin and bearing. The fuel/oil mixture is injected into the boost-port side of the cylinder. At higher rpm, oil is also injected into the crankcase through a slot in the piston. The setup, according to Arctic Cat, improves performance,emissions and fuel economy.
The Ski-Doo* E-TEC* offers another example. Like many cars and trucks today, the E-TEC uses direct injection. Placing the fuel injectors directly in the combustion chamber allows precise control over the injection event, which improves power and reduces emissions. This arrangement, however, comes with challenges. In a traditional two-stroke engine, fuel and oil are mixed prior to being ingested by the engine, which helps the oil flow at lower temperatures since fuel reduces oil viscosity. In the E-TEC, fuel and oil are mixed only in the combustion chamber, so the bottom end of the engine – the crankshaft and rods – are lubricated by oil alone, making the oil’s cold-flow properties critical.
The bottom line is two-strokes require higher-quality oils than before. In the snowmobile market specifically, an oil must excel in three areas: cold-flow, piston protection and exhaust power valve cleanliness. AMSOIL Interceptor, our primary snowmobile recommendation, is proven to excel in all three areas. In 50 hours of extreme dyno testing, it completely prevented ring sticking and piston scuffing. It also boasts a -72°F cold-flow ability. Check the the performance testing of AMSOIL Interceptor 2-stroke oil.amsoil.com/proof
AMSOIL has invested countless hours in our Mechanical Test Lab, in the field and on the racetrack fine-tuning our two-stroke oils to deliver the benefits of today’s two-stroke engines need. As the two-stroke market continues to evolve, you can bet we’ll continue to develop and manufacture synthetic two-cycle oils that meet and even exceed the demands of today’s toughest 2-stroke engines, regardless of who builds them.
AMSOIL manufactures an entire line of synthetic two-stroke engine oils. No matter if you are looking for pre-mix oil for your weedeater/blower or maybe marine oil for that outboard fishing boat or your dirt bike we have you covered. Check out the entire line!
*All trademarked names are the property of their respective owners and may be registered marks in some countries.No affiliation or endorsement claim, express or implied, is made by their use.